Guide · updated 2026-11-19

When to call a technician

Some codes are a cleaning job. Some are a board, a driver, a motor, a laser, or a timing adjustment. The difference is worth knowing before you pick up a screwdriver.

The line

FaultDesk pages tell you when a code is a technician job. The general rule is simple: if the fix involves any of the following, stop and call someone qualified.

  • A board or a driver. Power boards, driver boards, and control boards are not swap-and-see parts. A wrong board or a bad connector can damage the replacement.
  • A motor or an encoder. A motor that is forced, or an encoder that is adjusted without the procedure, can lose the machine's position.
  • A laser. Laser alignment and safety are not a guess. Do not open the laser housing.
  • Timing or hook adjustment. The hook and the needle have to meet at the right point. A small error bends needles and breaks thread; a large one damages the hook.
  • A safety switch or the power supply. Never bypass an emergency stop, a door switch, or a safety interlock. Never open the power supply.

What to have ready before you call

  • The brand, model, and serial number. The serial matters when a manufacturer changed the board or the firmware mid-series.
  • The exact code, plus any second line or axis/needle number on the display.
  • What you already tried: re-threaded, cleaned the sensor, replaced the needle, restarted, reseated a connector. Say what changed, if anything.
  • When it happens: at startup, at speed, at a colour change, on a particular needle, after a long run, or only with one design.
  • A photo of the display and, if it is safe to take one, a photo of the part the code names.

How to describe the fault

A short, specific message gets a faster answer than "it's broken". Use this shape:

Model: Tajima TMFX, serial ...
Code: 291, upper thread breakage
When: after about 8,000 stitches, needle 7
Tried: re-threaded, new needle, cleaned the thread sensor
Changed: nothing; the same design ran yesterday
Need: next step or a service visit

If the machine is mid-order, say so. A technician can often prioritise a machine that is holding up a delivery, and the repair desk can route the request with that context.

What not to do

  • Do not open the power supply or the laser housing.
  • Do not bypass a safety switch to "get the order out".
  • Do not swap boards between machines to test them.
  • Do not force a jammed axis or a stuck frame.
  • Do not keep resetting a code that returns; the repeated reset can make the mechanical damage worse.

If you are not sure

Start with how to read a code, then open the code page. If the page says a board, driver, motor, laser, or timing is involved, that is your answer. If the page lists a mechanical check, do that one first and test on scrap. The system pages are a good place to see whether the fault is in a system you can safely inspect.

Repair deskNo. ______

Still down?

Send this code to a technician. Tell us the model and what the machine is doing. We’ll reply with the next step: a remote check, a part, or someone who services your area.

Request a repair callback →

No account. No charge to ask. If the machine is mid-order, say so in the notes.

FAQ

Can I replace a board myself?

Only if you are qualified and the manufacturer's procedure says so. A board swap can damage the replacement or hide the original fault. FaultDesk treats board, driver, motor, laser, and timing work as technician jobs.

What information does a technician need?

Brand, model, serial number, the exact code, what you already tried, when the fault happens, and whether the machine is holding up production. A photo of the display helps.

Is a stop code always a fault?

No. Some stop codes are normal safe stops, such as an upper thread break or a trim. The code page says whether the source lists a specific check, and the type is printed under the title.

Read next: How to read an embroidery machine error codeThread break checklist.

Independent and unofficial. General maintenance advice, not a substitute for the manual for your exact model. Corrections: see Method & disclaimer.