Tajima error list

Tajima error codes

122 codes and messages from the public The Embroidery Warehouse — Tajima Machine Error List. Search by code, meaning, or system.

CodeMeaningTypeSystems
01No 500 character function code when data set is seterror
02Tajima tape complement error. ( The same +/-- numerics are entered…errordesign
03Data is involved in the tape end codeerror
04Improper function code position. Or, wrong tape format was selectederror
06Memory writing errorerrormemory
08PTR tape signal troubleerrorsensor
09PTR motion is in disorder. Reader does not read the tape for more…errorcommunication
11Data set incompleteerror
1B1Stop due to frame stepping codestop codeframe
1C1Stop occurred because bar switch was pressed during frame steppingstop codeframe
1D1Stop at the start of all-head embroidery due to the stop settingstop code
12Excessive stitch backerrormemorydesign
1B2Stop due to stop codestop codeframe
1C2Stop by manual ATH operationstop codeframe
1D2Stop by preset haltstop code
13Prohibited forward ( When offset is set)errorframe
1B3Stop due to end code 1stop codeframe
1B4Stop due to thread trimming codestop codethreadtrimmer
1B5Stop due to a sequin codestop code
16Tape format 5 is selected although no designs are stored in memoryerrormemorydesign
1B6Stop due to automatic free setting offset codestop code
17After 30 designs have been stored in memory, tape format 2, or 4…errormemorydesign
18After the data setting, the number of that design is erasederrormemorydesign
19Memory capacity shortage during editingerrormemorydesign
2B1No response from serial deviceerrordesigncommunicationpneumatic
2C1The machine is started or frame forward/back is executed during…errorframe
2D1Initial setting of laser power is not completeerrorlaserpower
2B2TAJIMA code complement error. Same + anderrordesign
2C2ON is set for both boring and laser unit)errorlaserpower
2B3Data exists in an end codeerrordesign
2C3"Pack" is not designatederrordesign
2E3Power supply has been interrupted during embroideryerrorpower
2B4Code format error (A stitch code does not exist at the third…errordesign
2C4The design stitch count is exceedederrordesign
2B5Reading error, stitch data over 5.1 mmerrordesign
2C5An attempt was made to carry out laser processing during laser…errorlaser
2B6The serial interface is not readyerrorcommunication
2C6Machine operation was attempted, although the bobbin changer was…errorbobbin
2B7The machine was started or frame forward was performed although…errorframe
2B8When the pre-reading buffer becomes emptyerrormotorframedesign
2B9Memory write errorerrormemory
211A fixed position signal is not detected. Main shaft Z signalerrormotorencodersensor
212Needle bar is in lowering positionerrorneedle
221The frame has traveled left, exceeding the position set by the…errorframedesign
222The frame has traveled right, exceeding the position set by the…errorframedesign
223The frame has traveled up, exceeding the position set by the frame…errorframedesign
224The frame has traveled down, exceeding the position set by the…errorframedesign
225Travel outside the set embroidery areaerrorframedesign
226Absolute origin limit (+X, -Y) detectederrorframe
228Table up/down operation was attempted although the frame was in…errorframe
234Faulty laser uniterrorlaserpower
242M-axis rotation range exceedederror
251Low oil in the auto lube pumperrorlubrication
252The status of the air valve (vacuum) does not changeerrorpneumatic
253Lower limit of the laser protect cover is not detectederrorsensorlaserpneumatic
254Upper limit of the laser protect cover is not detectederrorsensorlaserpneumatic
255A peripheral device is defectiveerror
272Manual nipple lifting is performed during coiling embroideryerrorlubrication
281Target needle position not detectederrorneedlesensor
291Upper thread Breakage is detected. Tension base card is faultyerrorthreadbobbintension
293Under thread breakage is detectederrorthreadbobbin
30Stop command by bar switch is given during execution of mode 5, 6,…error
31Stop command by bar switch is given during color changeerror
3A1The thread trimming driver has issued abnormal signalserrorthreadtrimmersensor
3C1Power switched on while bar switch was heldstop codepower
3D1There is abnormality in a battery backup signalerrorsensordesignpower
3F1Thread tension control failureerrorthreadtension
32AHidden Error, usually occurs when the ATH functionserror
32FHidden Errorerror
3A2Thread trimming output time exceedederrorthreadtrimmer
3D2There is abnormality in a battery backup signalerrorsensordesignpower
3E2The p24R power supply is abnormalerrorpower
3F2Improper tension (tightness) errorerrortension
3D3There is abnormality in a battery backup signalerrorsensorpower
3F3The thread tension release driver has received an abnormal signalerrorthreadsensortension
3D4A ROM data check sum is abnormalerror
3B5Communication error in the controllererrorcommunicationpower
3D5There is an abnormality in the RAM data checksumerrormemory
3A6ATH movable knife retract positionerrortrimmer
3B6Communication problemerrorcommunication
3D6There is abnormality in the program or CPU card The software is…error
3D7There is abnormality in the main shaft motor speed control dataerrormotor
3A8A thread holding driver error signal is detectederrorthreadsensor
311Encoder A signal status does not change for 5 seconds. Motor or…errormotorencodersensor
312Encoder z signal status does not change for 5 secondserrorencodersensor
313Clutch stopper disengagederror
314Main shaft rotation failureerrormotorencodersensorpower
316A main shaft driver error is detectederrormotor
317The take-up lever clutch has received an abnormal signalerrorsensor
321PMD failureerrormotor
322An X-axis pulse motor driver error signal is detectederrormotorsensor
323A Y-axis pulse motor driver error signal is detectederrormotorsensor
324Frame feed output when the needle penetrates the fabricerrorneedleencoderframe
325Absolute origin could not be detected on the X or Y axis. Cap…errorframesensor
331Bobbin Changer errorerrorbobbin
341An M-axis base point signal is not detectederrorsensor
342An M-axis PMD abnormal signal is detectederrorencodersensor
345The M-axis clutch driver has received an abnormal signalerrorsensor
346The zig-zag PMD has received an abnormal signalerrorsensor
347An M-axis PMD abnormal signal is detectederrorsensor
352The sequin driver has issued abnormal signalserrorsensor
371Either an upper or lower position signal cannoterrorsensor
372The nipples do not move more than 1 seconderrormotor
373The nipple position sensor issued an abnormal signalerrorsensor
374Nipple sensor signal abnormality, both inputs have signalserrorsensor
375The Z-axis driver (Z-axis release solenoid) has received an…errorsensor
381FX head needle position input errorerrorneedlemotorsensor
382The needle position signal status during color change does not…errorneedlemotorsensorpower
383Incorrect input of needle positionerrorneedlemotorsensor
384Control error of the looper shaft driveerrorpower
385Lens does not move to the designated position when during lense…errorsensordesignpneumatic
391Thread release input signal errorerrorthreadsensor
51No stop position signal is outputerrorencodersensor
52Frame limit switch activatederrorframe
53Stepping motor driver trouble (X, Y)errormotor
54Left and right limits on the color change are detectederrorneedle
55Color change takes over 5 secondserror
56Color change, half-turn cam signal troubleerrorneedlesensor
57Needle position signal troubleerrorneedlesensor
58One turn of the main shaft motor takes over 5 secondserrormotor
59The cap frame moves more than 75mm from the cap frame zero point…errorframe
60The embroidery space of the cap frame is exceedederrorframedesign
Machine down right now? Send the Tajima code and model. We’ll reply with the next step.
Request a repair callback →
Source: The Embroidery Warehouse — Tajima Machine Error List. Manual-derived error list. Verify against your exact model and manual before repairing.