| Barudan | A01 | No or Low Battery Voltage Error | power |
| Barudan | A05 | Wrong Tape Code or BAUD Rate Error | designcommunication |
| Barudan | A07 | IC Memory Error | memory |
| Barudan | A08 | Memory is Full or Design Memory Read Error | memorydesign |
| Barudan | A11 | No PC or peripheral device connected | designcommunication |
| Barudan | A26 | Sock Frame Origin Not Set | frame |
| Barudan | A39 | USB Read/Write Error R m | memory |
| Barudan | A40 | Network Error | designcommunicationpower |
| Barudan | A41 | Design data reading error | design |
| Barudan | D01 | Needle Bar Not Locked | needlesensor |
| Barudan | D03 | Color Change Lock Error | sensor |
| Barudan | D04 | Color Change Needle Sensor Error | needlesensor |
| Barudan | D05 | Color Change Error | threadpower |
| Barudan | D06 | Main Motor Trip Error | motor |
| Barudan | D07 | Main motor overload | threadmotorlubrication |
| Barudan | D08 | Frame Limit Error | framedesign |
| Barudan | D09 | Start/Stop Switch Error | |
| Barudan | D11 | Rotary Encoder Error | encoder |
| Barudan | D12 | Trimmer slider error | threadtrimmerpneumatic |
| Barudan | D16 | Bobbin Break | threadbobbin |
| Barudan | D22 | Trimmer motor error | threadtrimmermotor |
| Barudan | D26 | Pulse Motor Circuit Overheat | motorframepower |
| Barudan | D29 | Servo Driver Error | framepower |
| Barudan | D30 | Head/Duct Board Switch Mo ON Error pr bo da | communication |
| Barudan | D31 | Driver Box/Board Communication Error | communication |
| Barudan | D33 | Power Interrupt Error | power |
| Barudan | D35 | Lubrication Error | |
| Barudan | D37 | Sequin Device Error | |
| Barudan | D38 | Chenille Driver Error | needlemotor |
| Barudan | D39 | Looper Motor Error | motorsensor |
| Barudan | D40 | Chenille Thread Clamp Motor Error | threadmotorsensortension |
| Barudan | D41 | Chenille Needle Height Error | needleframesensor |
| Barudan | D42 | Chenille Error | |
| Barudan | D43 | Presser Set Error | |
| Barudan | D44 | Lock Stitch Zig-Zag Driver | |
| Barudan | D45 | Lock Stitch Zig-Zag Tension | tension |
| Barudan | D46 | Lock Stitch Zig-Zag Error | |
| SWF | 101 | Main board or overload | threadbobbinneedletension |
| SWF | 102 | Main board or overload | threadbobbinneedletension |
| SWF | 103 | Trimmer knife did not return | threadneedletrimmerlubrication |
| SWF | 300 | Needle position signal | needleframe |
| SWF | 707 | Doc broken / flash memory | memorydesign |
| Tajima | 01 | No 500 character function code when data set is set | |
| Tajima | 02 | Tajima tape complement error. ( The same +/-- numerics are entered… | design |
| Tajima | 03 | Data is involved in the tape end code | |
| Tajima | 04 | Improper function code position. Or, wrong tape format was selected | |
| Tajima | 06 | Memory writing error | memory |
| Tajima | 08 | PTR tape signal trouble | sensor |
| Tajima | 09 | PTR motion is in disorder. Reader does not read the tape for more… | communication |
| Tajima | 11 | Data set incomplete | |
| Tajima | 12 | Excessive stitch back | memorydesign |
| Tajima | 13 | Prohibited forward ( When offset is set) | frame |
| Tajima | 16 | Tape format 5 is selected although no designs are stored in memory | memorydesign |
| Tajima | 17 | After 30 designs have been stored in memory, tape format 2, or 4… | memorydesign |
| Tajima | 18 | After the data setting, the number of that design is erased | memorydesign |
| Tajima | 19 | Memory capacity shortage during editing | memorydesign |
| Tajima | 2B1 | No response from serial device | designcommunicationpneumatic |
| Tajima | 2C1 | The machine is started or frame forward/back is executed during… | frame |
| Tajima | 2D1 | Initial setting of laser power is not complete | laserpower |
| Tajima | 2B2 | TAJIMA code complement error. Same + and | design |
| Tajima | 2C2 | ON is set for both boring and laser unit) | laserpower |
| Tajima | 2B3 | Data exists in an end code | design |
| Tajima | 2C3 | "Pack" is not designated | design |
| Tajima | 2E3 | Power supply has been interrupted during embroidery | power |
| Tajima | 2B4 | Code format error (A stitch code does not exist at the third… | design |
| Tajima | 2C4 | The design stitch count is exceeded | design |
| Tajima | 2B5 | Reading error, stitch data over 5.1 mm | design |
| Tajima | 2C5 | An attempt was made to carry out laser processing during laser… | laser |
| Tajima | 2B6 | The serial interface is not ready | communication |
| Tajima | 2C6 | Machine operation was attempted, although the bobbin changer was… | bobbin |
| Tajima | 2B7 | The machine was started or frame forward was performed although… | frame |
| Tajima | 2B8 | When the pre-reading buffer becomes empty | motorframedesign |
| Tajima | 2B9 | Memory write error | memory |
| Tajima | 211 | A fixed position signal is not detected. Main shaft Z signal | motorencodersensor |
| Tajima | 212 | Needle bar is in lowering position | needle |
| Tajima | 221 | The frame has traveled left, exceeding the position set by the… | framedesign |
| Tajima | 222 | The frame has traveled right, exceeding the position set by the… | framedesign |
| Tajima | 223 | The frame has traveled up, exceeding the position set by the frame… | framedesign |
| Tajima | 224 | The frame has traveled down, exceeding the position set by the… | framedesign |
| Tajima | 225 | Travel outside the set embroidery area | framedesign |
| Tajima | 226 | Absolute origin limit (+X, -Y) detected | frame |
| Tajima | 228 | Table up/down operation was attempted although the frame was in… | frame |
| Tajima | 234 | Faulty laser unit | laserpower |
| Tajima | 242 | M-axis rotation range exceeded | |
| Tajima | 251 | Low oil in the auto lube pump | lubrication |
| Tajima | 252 | The status of the air valve (vacuum) does not change | pneumatic |
| Tajima | 253 | Lower limit of the laser protect cover is not detected | sensorlaserpneumatic |
| Tajima | 254 | Upper limit of the laser protect cover is not detected | sensorlaserpneumatic |
| Tajima | 255 | A peripheral device is defective | |
| Tajima | 272 | Manual nipple lifting is performed during coiling embroidery | lubrication |
| Tajima | 281 | Target needle position not detected | needlesensor |
| Tajima | 291 | Upper thread Breakage is detected. Tension base card is faulty | threadbobbintension |
| Tajima | 293 | Under thread breakage is detected | threadbobbin |
| Tajima | 30 | Stop command by bar switch is given during execution of mode 5, 6,… | |
| Tajima | 31 | Stop command by bar switch is given during color change | |
| Tajima | 3A1 | The thread trimming driver has issued abnormal signals | threadtrimmersensor |
| Tajima | 3D1 | There is abnormality in a battery backup signal | sensordesignpower |
| Tajima | 3F1 | Thread tension control failure | threadtension |
| Tajima | 32A | Hidden Error, usually occurs when the ATH functions | |
| Tajima | 32F | Hidden Error | |
| Tajima | 3A2 | Thread trimming output time exceeded | threadtrimmer |
| Tajima | 3D2 | There is abnormality in a battery backup signal | sensordesignpower |
| Tajima | 3E2 | The p24R power supply is abnormal | power |
| Tajima | 3F2 | Improper tension (tightness) error | tension |
| Tajima | 3D3 | There is abnormality in a battery backup signal | sensorpower |
| Tajima | 3F3 | The thread tension release driver has received an abnormal signal | threadsensortension |
| Tajima | 3D4 | A ROM data check sum is abnormal | |
| Tajima | 3B5 | Communication error in the controller | communicationpower |
| Tajima | 3D5 | There is an abnormality in the RAM data checksum | memory |
| Tajima | 3A6 | ATH movable knife retract position | trimmer |
| Tajima | 3B6 | Communication problem | communication |
| Tajima | 3D6 | There is abnormality in the program or CPU card The software is… | |
| Tajima | 3D7 | There is abnormality in the main shaft motor speed control data | motor |
| Tajima | 3A8 | A thread holding driver error signal is detected | threadsensor |
| Tajima | 311 | Encoder A signal status does not change for 5 seconds. Motor or… | motorencodersensor |
| Tajima | 312 | Encoder z signal status does not change for 5 seconds | encodersensor |
| Tajima | 313 | Clutch stopper disengaged | |
| Tajima | 314 | Main shaft rotation failure | motorencodersensorpower |
| Tajima | 316 | A main shaft driver error is detected | motor |
| Tajima | 317 | The take-up lever clutch has received an abnormal signal | sensor |
| Tajima | 321 | PMD failure | motor |
| Tajima | 322 | An X-axis pulse motor driver error signal is detected | motorsensor |
| Tajima | 323 | A Y-axis pulse motor driver error signal is detected | motorsensor |
| Tajima | 324 | Frame feed output when the needle penetrates the fabric | needleencoderframe |
| Tajima | 325 | Absolute origin could not be detected on the X or Y axis. Cap… | framesensor |
| Tajima | 331 | Bobbin Changer error | bobbin |
| Tajima | 341 | An M-axis base point signal is not detected | sensor |
| Tajima | 342 | An M-axis PMD abnormal signal is detected | encodersensor |
| Tajima | 345 | The M-axis clutch driver has received an abnormal signal | sensor |
| Tajima | 346 | The zig-zag PMD has received an abnormal signal | sensor |
| Tajima | 347 | An M-axis PMD abnormal signal is detected | sensor |
| Tajima | 352 | The sequin driver has issued abnormal signals | sensor |
| Tajima | 371 | Either an upper or lower position signal cannot | sensor |
| Tajima | 372 | The nipples do not move more than 1 second | motor |
| Tajima | 373 | The nipple position sensor issued an abnormal signal | sensor |
| Tajima | 374 | Nipple sensor signal abnormality, both inputs have signals | sensor |
| Tajima | 375 | The Z-axis driver (Z-axis release solenoid) has received an… | sensor |
| Tajima | 381 | FX head needle position input error | needlemotorsensor |
| Tajima | 382 | The needle position signal status during color change does not… | needlemotorsensorpower |
| Tajima | 383 | Incorrect input of needle position | needlemotorsensor |
| Tajima | 384 | Control error of the looper shaft drive | power |
| Tajima | 385 | Lens does not move to the designated position when during lense… | sensordesignpneumatic |
| Tajima | 391 | Thread release input signal error | threadsensor |
| Tajima | 51 | No stop position signal is output | encodersensor |
| Tajima | 52 | Frame limit switch activated | frame |
| Tajima | 53 | Stepping motor driver trouble (X, Y) | motor |
| Tajima | 54 | Left and right limits on the color change are detected | needle |
| Tajima | 55 | Color change takes over 5 seconds | |
| Tajima | 56 | Color change, half-turn cam signal trouble | needlesensor |
| Tajima | 57 | Needle position signal trouble | needlesensor |
| Tajima | 58 | One turn of the main shaft motor takes over 5 seconds | motor |
| Tajima | 59 | The cap frame moves more than 75mm from the cap frame zero point… | frame |
| Tajima | 60 | The embroidery space of the cap frame is exceeded | framedesign |